Test version · not yet public

Pyrolysis cleaning · Midlands & North West

Long screws. Wide dies. Big filters. Cleaned in one piece.

Pyrolysis cleaning at Arena Comet UK near Stoke-on-Trent. A 5 m × 2 m × 2 m oven chamber takes the extrusion tooling that doesn't fit a standard cleaning oven, and the polymer comes off without scraping, cutting or burning off by hand.

  • 5 × 2 × 2 mpyrolysis chamber
  • Staffordshirequick M6 access via A500
  • 5 countriesArena Comet group
Open Santana pyrolysis oven at Arena Comet UK in Staffordshire, with a full car body on the loading floor to show the size of the chamber
Arena Comet UK · Newcastle-under-Lyme Santana pyrolysis oven Chamber 5 m long × 2 m wide × 2 m high. Shown here with a complete car body inside.

Polymer removed thermally, not mechanically

Long and wide parts in one piece

Collection & return can be arranged

Quote from a photo and dimensions

What we clean

The parts that clog your line, back to bare metal.

Polymer build-up, degraded material, paint and coatings are removed from steel and other heat-resistant metal parts. Typical work for plastics processors:

Extruder components such as mandrels, torpedoes and die parts after thermal cleaning

Screws & barrel components

Extruder screws, mixing sections, screw tips, torpedoes and breaker plates. Long screws go in whole, up to the length of the chamber.

Extrusion die plates and rings in a basket after pyrolysis cleaning

Extrusion dies

Pipe and profile dies, flat sheet and film dies, coat-hanger dies, die plates and mandrels. Wide dies cleaned without splitting them into sections first.

Spinneret plate, half covered in polymer before cleaning and half clean with open holes after cleaning

Spinnerets & spin packs

Spinneret plates, spin pack components and spin beam parts for fibre and monofilament lines. Every capillary open again.

Perforated industrial filter plate with polymer residue in the holes

Melt & candle filters

Candle filters, leaf and disc filters, screen changer plates and breaker plates. Polymer is removed from inside the filter media, not just the surface.

Hot runner nozzles with plastic residue before thermal cleaning

Hot runners & nozzles

Hot runner nozzles, manifolds and injection moulding parts. Tell us about heaters, thermocouples or seals so we can advise first.

Blow moulding head on an oven grid, ready for thermal cleaning

Blow moulding heads

Parison heads, accumulator heads and spiral mandrel distributors with their complex internal channels.

Static mixers & melt line parts

Static mixer elements and housings, adapters, gear pump parts and melt pipes, where polymer degrades in dead spots.

Powder-coated paint hangers and hooks with thick coating build-up, waiting to be stripped at Arena Comet UK

Paint racks, jigs & hooks

Paint and powder coating build-up removed from racks, jigs, hooks and hangers, so they make good earth contact again.

Before & after

What the oven leaves behind: clean metal.

Candle filter fully coated in solidified polymer before thermal cleaning
BeforeCandle filter with solidified polymer
Candle filter with clean pleated mesh after pyrolysis cleaning
AfterPleated mesh clean and open

Photos: Arena Comet UK and Arena Comet group.

How pyrolysis cleaning works

Heat does the work. Your tooling stays intact.

Scraping, torching or hard blasting a screw or die costs hours and risks scratched flow surfaces and damaged edges. Pyrolysis removes the polymer with a controlled thermal cycle instead.

  1. 01

    Controlled heating

    The part is loaded into the oven and heated on a programme chosen for the part and the polymer. The bulk of the plastic melts and drains off.

  2. 02

    Pyrolysis

    With little oxygen in the chamber, the remaining polymer breaks down into gases instead of burning on the part. The gases are destroyed in an afterburner.

  3. 03

    Controlled oxidation

    A final controlled stage removes the carbon left behind, leaving only a light, loose ash on the metal.

  4. 04

    Finishing

    Ash and inorganic fillers are rinsed or blown off, the part is cooled slowly, checked and prepared for return.

Operator rinsing ash from cleaned parts in a booth after thermal cleaning
Finishing: ash is rinsed off after the thermal cycle.

Sectors

Built for the people who keep lines running.

Written for maintenance and engineering managers at UK plastics processors and coating lines.

  • Pipe & profile extrusion

    Pipe heads, profile dies, extruder screws and breaker plates.

  • Film & sheet

    Flat dies, blown film dies, feedblocks and melt filters from cast and blown film lines.

  • Fibre & monofilament

    Spinnerets, spin packs, spin beam parts and filter candles.

  • Recycling & compounding

    Screen changer plates, melt filters, die plates and screw elements from contaminated feedstock.

  • Cable & wire

    Crossheads, tips and dies from cable insulation and sheathing lines.

  • Coating lines

    Paint racks, jigs, hooks and hangers from powder coating and wet paint lines.

Why Arena Comet UK

Big chamber. Central location. Specialists in thermal cleaning.

5m × 2m × 2m

A chamber for large tooling

Long extruder screws, wide sheet and film dies, spin beams, large melt filters and full paint racks fit in one piece. No cutting, splitting or partial cleaning.

Central UK location

Parkhouse Industrial Estate, Newcastle-under-Lyme, near Stoke-on-Trent, with quick access to the M6 via the A500. Well placed for the Midlands and the North West.

Experienced team

A team that cleans industrial parts every day and knows how polymers, coatings and tooling behave in the oven.

Part of the Arena Comet group

Arena Comet designs and builds thermal cleaning equipment and runs cleaning centres in Belgium, the UK, France, Poland and the Czech Republic.

One technical contact

Your enquiry is handled by a technical sales partner who knows the oven and the site, and who speaks the language of extrusion and maintenance.

From enquiry to clean part

Six steps. One point of contact.

  1. 1

    Send a photo

    Photo, dimensions, weight and polymer via the form below.

  2. 2

    Quote

    You receive a price and lead time for the cleaning.

  3. 3

    Collect or deliver

    Drop off in Newcastle-under-Lyme or we arrange collection.

  4. 4

    Clean

    Pyrolysis cycle programmed for your part and polymer.

  5. 5

    Inspect

    Ash removed and the part checked before release.

  6. 6

    Return

    Packed and returned, ready for your next run.

FAQ

Questions engineers ask us.

What is pyrolysis cleaning?

Pyrolysis cleaning removes polymer and other organic residue from metal parts with heat. In a controlled oven the plastic melts off and is broken down into gases, which are burned in an afterburner. A final controlled stage removes the remaining carbon, leaving a light ash that is rinsed or blown off. No scraping, cutting or aggressive blasting is needed to get the polymer off.

How big can parts be?

The Santana pyrolysis oven at Arena Comet UK has a chamber of 5 m × 2 m × 2 m. Long extruder screws, wide sheet and film dies, spin beams, large melt filters and paint racks can usually be cleaned in one piece. Send the dimensions and weight and we will confirm before you ship.

Which polymers can be removed?

Most common thermoplastics, such as PE, PP, PS, PET and PA, plus paints and powder coatings. Always tell us the polymer and any additives or fillers: some materials, for example PVC or fluoropolymers, need to be discussed before cleaning.

Will thermal cleaning damage my screw or die?

The cycle runs on a controlled temperature programme chosen for the part and the polymer, which is why pyrolysis is widely used for precision extrusion tooling. Tell us the steel, any surface treatment (nitrided, chrome-plated, bimetallic) and any non-metal components, and we will confirm the right programme before we start.

How long does it take?

It depends on the size of the part, the amount of polymer and the load in the oven. You receive a lead time together with the quote.

Can you collect and return parts?

Yes, collection and return can be arranged. The site is in Newcastle-under-Lyme, Staffordshire, with quick access to the M6 via the A500, so you can also drop parts off yourself during opening hours.

Do you also strip paint racks, jigs and hooks?

Yes. Paint and powder coating build-up on racks, jigs, hooks and hangers is removed in the same pyrolysis oven, so they make proper electrical contact again.

Who operates this website?

This website is operated by TuneItUp BV as official sales partner of Arena Comet UK Ltd. All cleaning work is carried out by Arena Comet UK Ltd at Unit 59 Brick Kiln Lane, Parkhouse Industrial Estate West, Newcastle-under-Lyme ST5 7AS.

Request a quote

Send us a photo. We'll tell you if it fits and what it costs.

The more we know, the faster and more accurate the quote: overall dimensions, weight, the polymer or coating, and how much build-up there is.

Where the work is done

Arena Comet UK Ltd
Unit 59 Brick Kiln Lane
Parkhouse Industrial Estate West
Newcastle-under-Lyme ST5 7AS
United Kingdom

Opening hours: Mon–Fri, 08:00–16:00

Enquiries via this website are handled by TuneItUp BV, official sales partner of Arena Comet UK Ltd.

Test version: submissions are not emailed to anyone yet. Your details are only used to answer your enquiry.

Get a quote