
Screws, barrels & mixing parts
Extruder screws, mixing sections, screw tips and torpedoes. Long screws go in whole, up to the length of the chamber.
Plastic removal · Extrusion & injection moulding
Burnt-on plastic and degraded polymer taken off steel tooling at Arena Comet UK near Stoke-on-Trent. A 5 m × 2 m × 2 m pyrolysis oven takes long screws and wide dies in one piece, without scraping, wire brushes or torches.
Polymer removed thermally, not mechanically
Long screws and wide dies in one piece
Collection & return can be arranged
Quote from a photo and dimensions
What we clean
Polymer build-up and degraded material are removed from steel and other heat-resistant metal parts. Typical work for extruders and moulders:

Extruder screws, mixing sections, screw tips and torpedoes. Long screws go in whole, up to the length of the chamber.

Pipe and profile dies, die plates, mandrels and spiders. Plastic is removed from inside the flow channels too.

Breaker plates, screen changer plates and filter plates with polymer in every hole.

Hot runner nozzles, manifolds, injection nozzles and moulding parts. Tell us about heaters, thermocouples or seals so we can advise first.

Parison heads, accumulator heads and spiral mandrel distributors with complex internal channels.
Static mixer elements and housings, adapters, gear pump parts and melt pipes, where polymer degrades in dead spots.
Before & after




Photos: Arena Comet UK and Arena Comet group.
How it works
Scraping, torching or hard blasting a screw or die costs hours and risks scratched flow surfaces and damaged edges. Pyrolysis removes the plastic with a controlled thermal cycle instead.
The part is loaded into the oven and heated on a programme chosen for the part and the polymer. The bulk of the plastic melts and drains off.
With little oxygen in the chamber, the remaining polymer breaks down into gases instead of burning on the part. The gases are destroyed in an afterburner.
A final controlled stage removes the carbon left behind, leaving only a light, loose ash on the metal.
Ash and inorganic fillers are rinsed or blown off, the part is cooled slowly, checked and prepared for return.
After the oven
After pyrolysis the parts can go straight back to you. If you need them cleaner, or ready for re-coating or re-covering, a finishing step can be added. Blasting is available on request and can be arranged for UK customers. We confirm what is possible when we quote and agree it with you per job.
Parts go back to you as they come out of the oven. Very often, but not always, with a light ash or dust residue on them, which many customers simply blow, wipe or wash off themselves.
Ash and loose residue washed off with a high-pressure washer, so the parts come back visibly clean.
Fine holes, mesh and tight channels cleaned in an ultrasonic bath after the oven. Suited to precision parts.
On request. A gentle blast for delicate parts, leaving a clean, even finish.
On request. Takes off the last residue and leaves the metal with a uniform, slightly rough surface.
On request. A heavier blast for robust steel parts that must go back into the line or be re-coated.
Typical for dies, nozzles and hot runner parts: an ultrasonic bath. Where a surface finish matters, tell us which surfaces must not be touched so we can choose the gentlest option.
Why Arena Comet UK
5m × 2m × 2m
Long extruder screws, wide dies and large filter housings fit in one piece. No cutting, splitting or partial cleaning.
Parkhouse Industrial Estate, Newcastle-under-Lyme, near Stoke-on-Trent, with quick access to the M6 via the A500. Well placed for the Midlands and the North West.
A controlled temperature programme per part and polymer, instead of scraping, wire brushing or torching that can mark flow surfaces.
Arena Comet designs and builds thermal cleaning equipment and runs cleaning centres in Belgium, the UK, France, Poland and the Czech Republic.
Your enquiry is handled by a technical sales partner who speaks the language of extrusion, moulding and maintenance.
From enquiry to clean part
Photo, dimensions, weight and material via the form below.
You receive a price and lead time for the job.
Drop off in Newcastle-under-Lyme or we arrange collection.
Pyrolysis cycle programmed for your part.
Ash removed and the part checked before release.
Packed and returned, ready for your next run.
FAQ
Pyrolysis is the usual industrial answer. The screw is heated on a controlled programme so the polymer melts, breaks down into gas and leaves a light ash that is rinsed or blown off. Nothing scrapes the flights or the root, which is how screws are normally damaged by wire brushes, scrapers and torches. Tell us the steel and any surface treatment so we can set the programme.
Burnt, carbonised plastic is hard to remove mechanically without marking the part. Thermal cleaning breaks it down with heat instead. Send a photo, the polymer and the size of the screw, nozzle or non-return valve, and we will say how we would clean it.
Often yes, but the surface treatment matters. Tell us the steel, any nitriding, chrome plating or bimetallic liner, and any non-metal parts, and we will confirm the right programme before we start.
Most common thermoplastics, such as PE, PP, PS, PET and PA, plus other polymers and coatings. Always tell us the polymer and any additives or fillers: some materials, for example PVC or fluoropolymers, need to be discussed before cleaning.
The chamber of the Santana pyrolysis oven is 5 m long, 2 m wide and 2 m high. Send the length, diameter and weight and we will confirm it fits before you ship.
Yes, as long as the heaters, thermocouples and seals are removed or the part is built to take the heat. Tell us how the manifold or nozzle is built and we will advise first.
Your technical contact
Your parts are cleaned by Arena Comet UK in Newcastle-under-Lyme, and you deal with Bart. He installed and maintained Arena cleaning machines at customer sites as a field service technician, and later started up and ran Arena's UK cleaning centre in Stoke himself. He gives you honest advice on whether a part suits pyrolysis, answers quickly and follows the job from first photo to return.
+32 472 79 31 43 · bart.joris@tuneitup.be
Official sales partner of Arena Comet UK Ltd (company no. 13989168) · TuneItUp BV, company no. BE 1043.282.906, Noordlaan 10A/8, 9200 Dendermonde, Belgium.
Other services
Request a quote
The more we know, the faster and more accurate the quote: overall dimensions, weight, the material and how much build-up there is.
Opening hours: Mon–Fri, 08:00–16:00
Bart Joris: +32 472 79 31 43 · bart.joris@tuneitup.be
Enquiries via this website are handled by TuneItUp BV, official sales partner of Arena Comet UK Ltd.