Test version · not yet public

Spinnerets · Melt filters · Film dies

Spinneret, spin pack and melt filter cleaning. Every hole open again.

Spinnerets and spin packs are cleaned by pyrolysis in the Santana oven at Arena Comet UK near Stoke-on-Trent. Polymer baked into capillaries and filter media is removed with heat, and wide film and sheet dies fit the 5 m × 2 m × 2 m chamber too.

  • 5 × 2 × 2 mpyrolysis chamber
  • Inside the medianot just the surface
  • Film & sheet dieswide dies in one piece
Spinneret plate, half covered in polymer before cleaning and half clean with open holes after cleaning
Before and after Spinneret plate Left: polymer in the holes. Right: open holes after thermal cleaning.

Polymer removed from inside filters and holes

Wide dies in one piece

Collection & return can be arranged

Quote from a photo and dimensions

What we clean

Fine holes, filter media and wide dies, cleaned thermally.

Fibre, film and compounding lines clog with polymer in places you cannot reach with a tool. Typical work:

Spinneret plate, half covered in polymer before cleaning and half clean with open holes after cleaning

Spinnerets

Spinneret plates and capillary plates for fibre and monofilament lines. Send hole size and tolerances if they are critical.

Spin pack component covered in solidified white polymer before thermal cleaning

Spin packs & spin beam parts

Spin pack components, spin beam parts and distribution plates. Tell us how the pack is built and which parts must be dismantled.

Perforated industrial filter plate with polymer residue in the holes

Melt & polymer filters

Leaf and disc filters, screen changer plates and filter plates. Polymer is removed from inside the filter media.

Candle filter fully coated in solidified polymer before thermal cleaning

Candle filters

Pleated candle filters fouled with polymer from recycling and compounding lines.

Round breaker plate with a perforated pattern of holes

Breaker plates & die plates

Breaker plates, pelletiser die plates and granulating nozzles with polymer in hundreds of holes.

Wide film & sheet dies

Flat sheet dies, cast and blown film dies and coat-hanger dies. The chamber is 5 m long, so wide dies often go in unsplit.

Before & after

What the oven leaves behind: open holes and clean media.

Candle filter fully coated in solidified polymer before thermal cleaning
BeforeCandle filter with solidified polymer
Candle filter with clean pleated mesh after pyrolysis cleaning
AfterPleated mesh clean again
Spinneret plate, half covered in polymer and half clean with open holes
Before / afterSpinneret: polymer left, clean right
Perforated industrial filter plate with polymer residue in the holes
BeforeFilter plate with polymer in the holes

Photos: Arena Comet UK and Arena Comet group.

How it works

Heat reaches the places a tool cannot.

Brushing, drilling or soaking fine holes and filter media is slow and risks damage. Pyrolysis removes polymer from inside the holes and the media with a controlled thermal cycle.

  1. 01

    Controlled heating

    The parts are loaded into the oven and heated on a programme chosen for the part and the polymer. The bulk of the polymer melts and drains off.

  2. 02

    Pyrolysis

    With little oxygen in the chamber, the remaining polymer breaks down into gases instead of burning in the holes. The gases are destroyed in an afterburner.

  3. 03

    Controlled oxidation

    A final controlled stage removes the carbon left behind, leaving only a light, loose ash.

  4. 04

    Finishing

    Ash is rinsed or blown out of the holes and media, the parts are cooled slowly and the openings are checked before return.

Operator rinsing ash from cleaned parts in a booth after thermal cleaning
Finishing: ash is rinsed off after the thermal cycle.

After the oven

Finishing options, if you want the parts ready for the next step.

After pyrolysis the parts can go straight back to you. If you need them cleaner, or ready for re-coating or re-covering, a finishing step can be added. Blasting is available on request and can be arranged for UK customers. We confirm what is possible when we quote and agree it with you per job.

Straight back

Parts go back to you as they come out of the oven. Very often, but not always, with a light ash or dust residue on them, which many customers simply blow, wipe or wash off themselves.

Often used here

High-pressure wash

Ash and loose residue washed off with a high-pressure washer, so the parts come back visibly clean.

Often used here

Ultrasonic bath

Fine holes, mesh and tight channels cleaned in an ultrasonic bath after the oven. Suited to precision parts.

Often used here

Glass bead blasting

On request. A gentle blast for delicate parts, leaving a clean, even finish.

Sand blasting

On request. Takes off the last residue and leaves the metal with a uniform, slightly rough surface.

Shot blasting

On request. A heavier blast for robust steel parts that must go back into the line or be re-coated.

Typical for spinnerets, filters and dies: an ultrasonic bath after the oven to flush ash out of fine holes and mesh. Glass bead blasting on request for delicate parts.

Why Arena Comet UK

Big chamber. Central location. Specialists in thermal cleaning.

5m × 2m × 2m

A chamber for wide dies

Wide film and sheet dies, spin beams and large filter housings fit in one piece. No splitting or partial cleaning.

Central UK location

Parkhouse Industrial Estate, Newcastle-under-Lyme, near Stoke-on-Trent, with quick access to the M6 via the A500. Well placed for the Midlands and the North West.

Part of the Arena Comet group

Arena Comet designs and builds thermal cleaning equipment and runs cleaning centres in Belgium, the UK, France, Poland and the Czech Republic.

Inside the holes, not just the surface

Thermal cleaning reaches polymer in capillaries, filter media and channels that mechanical cleaning cannot reach.

One technical contact

Your enquiry is handled by a technical sales partner who knows the oven and the site.

From enquiry to clean part

Six steps. One point of contact.

  1. 1

    Send a photo

    Photo, dimensions, weight and material via the form below.

  2. 2

    Quote

    You receive a price and lead time for the job.

  3. 3

    Collect or deliver

    Drop off in Newcastle-under-Lyme or we arrange collection.

  4. 4

    Clean

    Pyrolysis cycle programmed for your part.

  5. 5

    Inspect

    Ash removed and the part checked before release.

  6. 6

    Return

    Packed and returned, ready for your next run.

FAQ

Questions about spinneret and filter cleaning.

How do you clean a spinneret or spin pack?

By pyrolysis in our Santana oven. The part is heated on a controlled programme so the polymer melts out, breaks down into gas and leaves only a light ash, which is rinsed or blown out of the holes. Nothing needs to be drilled, picked or scraped, so the capillaries are not touched mechanically.

Can you clean assembled spin packs?

Many spin packs are cleaned dismantled, because seals, gaskets and sensors may not take the heat. Tell us the pack type and what is fitted, and we will advise before you ship.

How do you clean polymer melt filters and candle filters?

Thermal cleaning removes polymer from inside the filter media, not just from the surface. Candle filters, leaf and disc filters and screen changer plates are loaded in baskets and run through the same cycle. Tell us the filter material and mesh so we can set the programme.

Can you clean a wide film die or sheet die?

The chamber is 5 m long, 2 m wide and 2 m high, so many wide flat dies, sheet dies and film dies fit without splitting. Send the dimensions and weight and we will confirm.

Will the holes be fully open when you return the part?

Thermal cleaning leaves only a light ash, which is rinsed or blown out, and the openings are checked before return. If hole size and tolerance are critical, send a drawing or the specification with your enquiry.

How often should spinnerets and filters be cleaned?

That depends on your polymer, throughput and filtration. We do not set your maintenance interval, but we can look at how your parts come back and tell you what we see.

Your technical contact

Bart Joris, official sales partner of Arena Comet UK.

Your parts are cleaned by Arena Comet UK in Newcastle-under-Lyme, and you deal with Bart. He installed and maintained Arena cleaning machines at customer sites as a field service technician, and later started up and ran Arena's UK cleaning centre in Stoke himself. He gives you honest advice on whether a part suits pyrolysis, answers quickly and follows the job from first photo to return.

+32 472 79 31 43 · bart.joris@tuneitup.be

Request a quote

Send us a photo. We'll tell you if it fits and what it costs.

The more we know, the faster and more accurate the quote: overall dimensions, weight, the material and how much build-up there is.

Where the work is done

Arena Comet UK Ltd
Unit 59 Brick Kiln Lane
Parkhouse Industrial Estate West
Newcastle-under-Lyme ST5 7AS
United Kingdom

Opening hours: Mon–Fri, 08:00–16:00

Bart Joris: +32 472 79 31 43 · bart.joris@tuneitup.be

Enquiries via this website are handled by TuneItUp BV, official sales partner of Arena Comet UK Ltd.

Test version: submissions are not emailed to anyone yet. Your details are only used to answer your enquiry.

Get a quote